產品展示

相關文章

產品展示

首頁 > 產品展示 > > 其他檢測儀器 > TC-500 氧氮聯合測定儀

TC-500 氧氮聯合測定儀

簡要描述：簡單說明：TC500系列儀器質量、性能、工藝滿足您對金屬、難熔物、其他無機材料日常生產中氮/氧分析的需要

產品型號：TC-500
廠商性質：生產廠家
更新時間：2025-07-17
訪問 量：2444

產品咨詢聯系我們

詳情介紹

詳細說明:

TC500系列儀器質量、性能、工藝滿足您對金屬、難熔物、其他無機材料日常生產中氮/氧分析的需要

Determination of Oxygen and Nitrogen in

Reactive/Refractory Metals and Their Alloys*

Approval

ASTM E-1409 Oxygen Determination in Titanium and Titanium Alloys

ASTM E-1569 Oxygen Determination in Tantalum

ASTM E-1937 Nitrogen Determination in Titanium and Titanium Alloys

Sample Preparation

A clean representative sample is required in order to obtain optimum results. Solid samples can be leached in suitable acid or abraded with a clean file, rinsed in acetone, and dried with warm air. Refer to ASTM methods above for further details.

Accessories

782-720 Crucible; 782-721 Electrode Tip; 502-344 UHP Nickel

Baskets; 501-073 Graphite; 503-032 Glass Accelerator Scoop;

501-059 Tin Capsules—for powdered samples. （Additional steps required for powdered samples are noted in parenthesis.）

Calibration Standard

LECO 501-320 Titanium Pin, 502-047 Zirconium Pin, NIST, or other suitable reactive/refractory metal standard.

Method Parameters

Analysis Parameters

Outgas Cycles 2

Analysis Delay （seconds） 20

Analysis Comparator 1

Analysis Type Auto

Element Parameters Oxygen Nitrogen

Minimum Time （seconds）	35	55
Integration Delay （seconds）	5	15
Comparator Level （%）	1	1

Furnace Parameters

Furnace Control Mode Power

Purge Time （seconds） 15

Outgas Time （seconds） 20

Cool Time （seconds） 5

Outgas Power （Watts） 6300

Analyze Power （Watts） 5300

*This includes Ti, Zr, W, Mo, Ta, Nb, Hf, and their alloys.

TC500

Typical Results
Titanium Pin	Mass （g）	Oxygen （%）	Nitrogen （%）
	0.1135	0.1808	0.0189
	0.1133	0.1843	0.0194
	0.1134	0.1831	0.0184
	0.1138	0.1819	0.0188
	0.1133	0.1821	0.0195
	0.1131	0.1829	0.0185
	0.1134	0.1833	0.0191
	0.1143	0.1849	0.0194
	0.1125	0.1837	0.0189
	0.1072	0.1830	0.0191
	Average	0.1830	0.0190
	Std. Dev.	0.0012	0.0004
Zirconium Wire	Mass （g）	Oxygen （%）	Nitrogen （%）
	0.1067	0.1246	0.0017
	0.0978	0.1273	0.0017
	0.1180	0.1246	0.0019
	0.1097	0.1235	0.0014
	0.1141	0.1272	0.0017
	0.1017	0.1226	0.0018
	0.1140	0.1269	0.0020
	0.0987	0.1239	0.0020
	0.1015	0.1233	0.0022
	0.1197	0.1270	0.0020
	Average	0.1251	0.0018
	Std. Dev.	0.0018	0.0002
Procedure

1. Determine the blank as follows:

a. Enter the "blank" ID code with a 1.0000 g weight in the weight stack.

b. Press the loader control switch, the sample loader will open.

c. Place one 502-344 UHP Nickel basket into the loading head using clean tweezers.

（Place a 501-059 Tin capsule into the Nickel basket before placing it in the loading head.）

d. Press the loader control switch, the sample loader will close and seal and the furnace electrode will open.

e. Remove crucible from electrode tip and discard. Clean furnace area using the appropriate brushes. Vacuum away loose dust.

f. Place ~0.05 g 501-073 into the bottom of a 782-720 crucible. ~0.05 g is approximay a ¼ full

503-032 glass accelerator scoop.

g. Place the crucible on the lower electrode.

h. Press the loader control switch, the furnace electrode will close and the analysis sequence will start automatically.

i. Repeat steps 1a through 1h at least four more times.

j. Enter blank following routine outlined in operator's instruction manual.

2. Calibrate the instrument as follows:

a. Weigh the calibration sample. （Weigh the calibration sample into the tin capsule.）

b. Enter the calibration sample ID code and sample weight in the weight stack.

c. Place the calibration sample （capsule） into a nickel basket.

d. Press the loader control switch, the sample loader will open.

e. Carefully place the calibration sample/nickel basket （capsule） into the loading head using clean tweezers. Make sure that the calibration sample （capsule） stays in the basket and the basket

stays upright.

f. Press the loader control switch, the sample loader will close and seal and the furnace electrode will open.

continued on page 3

Procedure （continued from page 2）

g. Remove crucible from electrode tip and discard. Clean furnace area using the appropriate brushes. Vacuum away loose dust.

h. Place ~0.05 g graphite into the bottom of a crucible.

i. Place the crucible on the lower electrode.

j. Press the loader control switch, the furnace electrode will close and the analysis sequence will start automatically.

k. Repeat steps 2a through 2j a minimum of three times.

l. Complete a calibration by following the auto calibration procedure as outlined in the operator's instruction manual.

m. Verify the calibration by analyzing the calibration sample again. It should fall within the expected tolerances. If not, repeat steps 2a through 2l again.

3. Analyze the samples as follows:

a. Weigh ~0.1 g sample. （Weigh the sample into the tin capsule.）

b. Enter the sample ID code and sample weight in the weight stack.

c. Place the sample （capsule） into a nickel basket.

d. Press the loader control switch, the sample loader will open.

e. Carefully place the sample/nickel basket （capsule） into the loading head using clean tweezers.

Make sure that the sample （capsule） stays in the basket and the basket stays upright.

f. Press the loader control switch, the sample loader will close and seal and the furnace electrode will open.

g. Remove crucible from electrode tip and discard. Clean furnace area using the appropriate brushes. Vacuum away loose dust.

h. Place ~0.05 g graphite into the bottom of a crucible.

i. Place the crucible on the lower electrode.

j. Press the loader control switch, the furnace electrode will close and the analysis sequence will start automatically.

Theory of Operation

The TC500 is a microprocessor-based, software-controlled instrument that measures both nitrogen and oxygen in a wide variety of metals, refractories, and inorganic materials. The inert gas fusion principle is employed. A weighed sample, placed in a high-purity graphite crucible, is fused under a flowing helium gas stream at temperatures sufficient to release oxygen, nitrogen, and hydrogen. The oxygen in the

sample, combines with the carbon from the crucible to form carbon monoxide. The nitrogen present in

the sample releases as molecular nitrogen, and any hydrogen present is released as hydrogen gas. The helium carries the sample gases through heated rare earth copper oxide which converts carbon

monoxide to carbon dioxide （CO2） and hydrogen to water （H2O）. The nitrogen passes through

unchanged. The gases are then passed through a CO2 infrared （IR） cell where the oxygen is measured as

CO2. CO2 and H2O are then removed by a Lecosorb/Anhydrone trap, while the nitrogen passes through

to a thermal conductivity （TC） cell for determination.

TC500 Flow Diagram

留言框

產品：
您的單位：
您的姓名：
聯系電話：
常用郵箱：
省份：
詳細地址：
補充說明：
驗證碼：

請輸入計算結果（填寫阿拉伯?dāng)?shù)字），如：三加四=7

上一條：CS600CS600高精度碳硫測定儀
下一條：TCH-600 TCH-600 氮?dú)溲趼?lián)合測定儀

最全日本精品网站在线观看,国产成人影视久久久综合,国产成人黄网站在线观看,国产精品欧美成人片

TC-500 氧氮聯合測定儀

留言框

產品：

您的單位：

您的姓名：

聯系電話：

常用郵箱：

省份：

詳細地址：

補充說明：

驗證碼：